A continuing journey into the psyche of Carl La Fong, world traveler, jack of all trades, soldier of fortune, adviser to kings and potentates and lover of beautiful women. All opinions are those of Carl. The author is to be held blameless for any death or dismemberment that may result from following any of the procedures contained herein. "What the world needs, is more geniuses with humility. There are so few of us left." Oscar Levant
Tuesday, August 16, 2011
Baby's In Black and I'm Feelin' Fine
After another hospital stay, I figured enough clowning around. I've missed the riding season due to a variety of issues, some unforeseen and some self imposed. Back to the shop. In the past week, I've managed to prep the frame and the side covers and get a nice coat of black acrylic lacquer on them. the covers came out pretty nice after the mods that I made to them and the frame looks real good as well. Once they're rubbed out, they'll really sparkle. Tomorrow I will actually begin re assembly. I should be able to get the frame wrapped around the engine, the fuel and cooling systems installed, the front end on and a bunch of other odds and ends. Maybe next month I can make some noise. Probably when I fall off of a ladder
The Prime Directive
The frame in primer. I did a bit of molding around the neck, the swing arm mounts and the rear frame gussets. I'll let it sit for a few days to finish drying and shrinking and then the lacquer goes on. The engine/trans are cleaned and detailed to LaFong standards. I replaced all of the bolts that I could with stainless socket head cap screws and those little snap in chrome caps. I got a new chrome intake manifold (thanks Stan) and stainless 12 point bolts from ARP. The fuel system is done, the clutch and shifter are very close, a couple of hours work and they'll be done. A few more welds and the swing arm will be done also. This will leave the rear fender that I have to widen and a modification to the tank that will be the subject of a future post.
Tuesday, August 9, 2011
Genesis or the Application of One's Self
"In the beginning, God created the Boy Genius™. He saw that he was good".
Well, it may not have been exactly that way, but it sounds good, huh? Actually it was slightly less dramatic. As a kid at Camellia Avenue Elementary School in the early 50s, I displayed some unusual talents. My art skills were quite advanced for a 5 year old and the teachers took note. I've posted a painting that I did in kindergarten and another that I did, almost 60 years later. Yeah, yeah, I know, "which one is which?" Later on as I learned to read, I was reading at a level far above the usual Dick and Jane stuff. I got into trouble for reading my entire textbook in a few days, rather than waiting for the whole class to struggle along, at one or two pages a day. Again, the teachers took note. It was during this time that someone decided that I should be tested. I'm not sure if it was to find out if I was bright or an idiot savant. They gave me the Stanford Binet IQ test. I scored 124. Now, this should have marked a turning point in my young life. However, this was the unenlightened 50s. I suppose I was expected to do better, at that point, without any outside influence. I was never guided into any special programs or counseled in any way. I was just told, every time that I screwed up, that I was a smart kid and that I should "apply" myself. My parents, who were good people, pretty much did the same. I don't know if they were intimidated, by a snot nosed kid who may have been smarter than they were, or not. So, all of this, and my life long inability to focus on anything for more than an hour or two, led to a school career marked by failure with occasional bursts of mediocrity. I graduated from high school with a low C average. I attended school in the Navy and did well because the curriculum interested me. Later I attended welding school with the same results. I never had to study during either course. That is the extent of my formal education. I bounced around, pretty much, the rest of my working life doing this and that. I was an embalmer, an auto body and paint guy, a teamster, a carpenter and a bunch of other stuff. I guess my failure to "apply" myself led to my failure to capitalize on my, alleged, talents.
So, to get to the point of all this. Little Carl was a 7 year old "Boy Genius™", Big Carl is a pretty smart guy. No more and certainly no less. Do I feel that I am smarter than everyone else? No, I do not. I feel that I am smarter than most, if not all, of the ditzels, dimwits and career under achievers that we all come into contact with every day. I can, usually, do the Sunday NY Times crossword puzzle. I can visualize a finished product while looking at a raw piece of material. I can do, basic, math. I can speak, spell and write reasonably well. I can dress myself. Am I still a Boy Genius™? Yes, absolutely. An adult genius ...........Nahhh, just Ol' Carl, the guy that knows how to do a variety of things with a fair degree of competence.
Saturday, June 4, 2011
Back on Track
Back to the subject of pulley alignment and tracking. On the V8BikeRiders website I have seen posts where riders have been advised to loosen their rear mounts and pry the transmission over to correct belt tracking problems. I would imagine that the engine/trans would tend to shift to the right under power. With this in mind, I slotted the mount holes on the rear cross member, that I built at the beginning of the build, to allow for adjustments later on. I also built this little gizmo to allow for easier tweeking of the belt tracking.
Wednesday, May 25, 2011
Square to the World
I spent 5 or 6 hours in the shop today shimming, prying, leveling, dropping plumb bobs, measuring, establishing center lines and so on. Things just didn't seem right. Nothing was the same from left to right or top to bottom. The long and short of it is, the engine did not sit in the frame straight or level. It was 3/16" low on the right side and skewed to the right about the same amount. I don't know why my belt tracked straight with everything so far out of whack. I thought, at first, that it might have been due to all of the mods that I made to install the Ranger, but the only, real, change was the rear mount which was built with the original front and top mounts in place. Of course, all this tweeking came at a cost. Now the swing arm mounts, that I built at the beginning of this saga, are misaligned. So, out came the smoke wrench and 2 minutes later they were off and laying on the floor. No drama other than the small brush fire in front of the building. I'm still pretty spry for 63. Ran, grabbed the hose, ran through the shop,dragging the hose, soaking everything in the process, out the front door and extinguished it. After catching my breath, I tacked the mounts back on. Everything is now coplanar. That is very important with a belt drive. Every component has to be at 90 or 180 degrees to each other. If not, there will be tracking problems. Some riders compensate for misalignment by cranking up the left adjuster. This is bad practice for several reasons. First is the one inch diameter axle and the large slider blocks in the swing arm. They do not allow for the axle to be "gimbled" over. What really happens is the swing arm and the bushings are placed under, even more, stress. The other thing is the belt is deformed. The belt is, basically, a cylinder. When you tweek it to one side to adjust tracking, it is forced into a slight taper or funnel shape. It will take a set as the fibers bed in. The only real solution is to be anal about setting everything straight. I'm glad that I noticed this before finishing the swing arm. I only want to build this last one
Saturday, May 21, 2011
Prototyping and Change Orders
I stayed pretty busy today. I generally go into the shop with high hopes of getting something done, but often end up being distracted. I suspect it's an ADD thing or sumpthin'. I rarely seem to work in a linear fashion, choosing instead to fiddle fart around with three or four minor projects instead. I made a mounting bracket for the fuel pressure regulator. I re assembled the paint free frame around the engine/trans unit. The transmission crossmember that I built previously will need some minor notching to clear the large front pulley. It actually clears as is, but I need a bit more so I can change the belt without splitting the frame. The old swing arm is another story entirely. It has been cut and welded too many times and the pivot mounts need to be altered to clear the pulley as well. So, it to, has been consigned to The Big Box O' Failures. I feel that Boy Geniuses™ rarely fail, so henceforth The BBOF shall be known as The Big Box O' Prototypes. Has a much more professional ring to it. I grabbed two more pieces of the 2 inch square tube that the first swing arm was made from, mounted them in the mill and cut the slots for the axle just as I did in January 2008. No need for pictures, same deal as before. Tomorrow I hope to make up the new pivot mounts. cut and weld the swing arm to put the bend in it and weld on the shock mounts. The new swing arm crossmember will be much simpler, hopefully, than the old cut, weld, cut weld, #*&%#*& lousy no good, cut weld again monstrosity. We'll see.
Friday, May 20, 2011
Strippin' and Slickin'
The past few days have been spent stripping off all of the old powder coat from the frame. It went fairly well. Boss Hoss didn't sandblast the frames prior to coating, so it didn't stick particularly well. Much of it practically fell of and paint stripper took care of the rest. A few passes with a 4" grinder with a wire wheel got into the nooks and crannys. Tomorrow I'll sandblast and begin slicking everything off with plastic filler and get it ready for primer. I was able to get good ol' lacquer primer/surfacer on line. I'm surprised that the tree huggers would allow it here in The Peoples Socialist Republik of Kalifornia. I have a new, unopened gallon of black acrylic lacquer that I dug out of the trash at work. Your tax dollars at work. Rest assured that an American Taxpayer will make good use of it. Some have said, "Why don't you just powder coat it?". Bondo and powder coat don't play well together. Lacquer has a look of it's own. Sorta warm and organic unlike the plasticky looking powder. Lacquer is totally forgiving. Chips and scratches are easy to fix. The real reason? Even though I have to buy the primer and thinner, the paint job will run less than a hundred bucks. Scrooge LaFong wins again. I think it's one of the Beatitudes, "The cheapskates shall inherit the good trash"
Subscribe to:
Posts (Atom)