Tuesday, May 10, 2011

Not the Same Old Shift



It's time to replace the ugly shifter that I cobbled up after the failed jockey shift episode. My idea was to find an old bicycle and use one of the crank arms as a shifter. After cruising a few yard sales, I found that junk bikes are still to much for the Po' Boy and most don't have the type of crank setup that I'm looking for. So, I grabbed a hunk of rectangular aluminum, put it between centers and cut away everything that doesn't look like a shifter. My lathe has a taper attachment that made it easy to come up with something that doesn't look home brewed. I stopped at the bicycle shop and bought a wedged cotter that most of the older bikes use to hold the crank arm on. I milled a flat on the shifter shaft and the cotter holds everything together nice and snug. At the same time, I moved the pivot up to the same axis as the clutch bell crank. This, of course, necessitated making a new bell crank since the old one had a little 3/8 bushing and the shifter uses 5/8. I cut it out with the torch, cleaned it up on the grinder and disc sander, made up a new hub, popped in a couple of bushings, added a Zerk and it's a done deal. Same for the lug that will weld to the frame. All in all it came out pretty good, I think

Thursday, April 14, 2011

Oh What A Tangled Web We Weave

It's time to address the wiring on my bike. The original harness looked as if it was made by a black widow spider on LSD. Additionally, it had been violated, repeatedly, by person or persons unknown who did not own a soldering iron, an assortment of crimp connectors or the crimping pliers. He (they) did, however, have an unlimited supply of electrical tape. I removed the entire harness and set it in front of me and went at it with knife and wire cutters. All I was left with was a few connectors and some lengths of wire. The factory wires with the application printed on them will, more than likely, be reused. Many of them will hit the trash can. There are no more electric pumps or tank valve so those circuits are no longer needed. The, mysterious, master relay will also disappear. I don't, quite, understand its function. I have wired a few cars and bikes over the years and none of them had a master relay. Another thing that will cut the number of wires to a minimum is the Grip Ace system http://www.gripace.com/ that I bought. The blinker, starter, high/low, and horn are all controlled by a touchpad that fits into the left grip. There are two, small wires that pull through the bars and connect to a module that controls all of the, previously mentioned, functions. All of the, sometimes, troublesome and bulky looking handlebar switches will go into the Big Box O' Unused, Unwanted and Unnecessary Parts. Simplification does have it's cost. I had to add a few relays that BH didn't originally us. I still have the fan and horn relays, but there are new ones for the lights, start circuit and the ignition. The new harness, when completed may be sent out and covered with, old style, cloth braiding. I have a local outfit that we used to use for our Austin Healey harnesses. Fortunately, for me, they're still in business. I do not like taped harnesses or the corrugated, split plastic loom tubing that most people use. Just too cheezy and off the shelf looking. The braided loom will look really nice next to the fuel lines. Most people will never see it. Those that do will, probably, not notice anything special but that's OK. I and other detail oriented folks will see the difference. Sorta like a secret handshake.

Friday, April 1, 2011

Trikes and Trikers


On a motorcycle website, that I frequent, many of the members ride trikes. Often, some of them feel compelled to defend their choice of rides. Excuses range from, they are too old or infirm and a trike is their only choice all the way to trikes are, quite simply, better. I have ridden a few trikes over the years and even built one in the 70's. As a certified Boy Genius™, I have my thoughts about two versus three wheels. Of course, I am going to share them. The following are the reasons people ride tricycles.
1. Too old or infirm to ride a two wheeler.
No problem there. We all have to do the best we can with what we have left.
2. They have more carrying capacity.
Yes they do. There is plenty of room for a change of undies, tampons, your large collection of, douchey looking, do rags, nail files, Depends etc. How do the two wheel guys manage?
3. They're safer.
No they're not. Avoiding objects in the road is more difficult. Swerving between lanes, in an emergency, is out.
4. They won't fall over at a red light.
Oh Brother!! Maybe you should take a bus. What makes you think you won't just fall off the damned thing at any given time.
5. My wife likes it better than a bike.
My wife would like it if I wore a tuxedo, threw away all of my crappy T shirts and took up embroidery so I could keep her company. I'm keeping my testicles right where they belong. I love my wife, but certain thing are sacrosanct.
6. There's really no difference.
Uh huh, and sex with a man is just as good if the lights are off. Motorcycles, the kind with two wheels, are a Zen sort of thing. If you are a true biker, you know what I mean. You become one with your machine. Your brain is wired to the whole bike. You can feel the engine, feel the tires as they contact the road. The bike/man leans, counter steers, makes minor corrections automatically. The trike is a three wheeled car, a hermaphrodite contraption, a compromise.
Will the Boy Genius™ ever own a trike? Only if or when I fall into the first category, too ancient or stove in to handle two wheels. Of course, the extra room for travel essentials will be nice and, maybe, Wifey will want to tag along from time to time. Hmmmm, lesse, a Richmond 5 speed, a Jag IRS. You don't think I would take the easy way, do you?

Monday, January 17, 2011

More Fuelishness





I have decided to remove the electric fuel pump from my bike and run a Race Pumps, piston style, pump. It will provide all of the fuel that I could ever ask for. It is not a cheap setup. The pump and regulator (you have to run theirs) run about 250 bucks. It is not a quick bolt on. A dimple needs to be made in the frame tube to allow the pump to fit. To make things even worse, I am re plumbing the whole system with black anodized AN fittings and black braided hose. I do not care for the looks of the braided stainless and the red and blue fittings that many choose to run. Too flashy for me. I know all of this seems to be overkill, but it looks so cool. I know of, at least, two BHs that have burned due to leaky fuel lines. I have never been a fan of worm clamps and auto part store rubber fuel line. The lines, that I put on during the Ranger swap, have already begun to get hard and show signs of aging.
Pix show the finished lines and pump. The AN fittings required a bit of finesse to install. The finish is quite fragile and ordinary wrenches will scar them. There are assembly tools available, but they are costly. I simply used a heavy piece of leather from an old belt and clamped the fitting in the vise. Using another hunk of leather i used a Visegrip to assemble the fitting to the hose. It sounds a bit brutal, but the fitting were scratch free after assembly.

Wednesday, December 8, 2010

Filling In The Blanks


Another thing that bothered me is the big ol' gaposis between the steering neck and the front of the tank. It is even more pronounced on the big block bikes. Today, I cut out a couple of pieces of steel and welded them in place between the neck and the tank mounts. This will look much better than staring at the wiring harness and all of the other, assorted dohickeys under the tank. BH should step up their game and pay more attention to detail on bikes in this price range. There are new players now and their bikes have no loose ends whatsoever.
Another rider filled in the tank tunnel with a piece of expanded mesh. It looks pretty nice, but I have another idea. Mine's not, necessarily, better than his, just different. I want to be different, just like everyone else.

Tuesday, December 7, 2010

Tune In, Turn On and Drop Out



No, Dr Leary isn't back from the dead. While the bike is apart, I decided to add a drop out crossmember. This modification allows the oil pan to be removed without dismantling the bike. This is not my innovation. It has been done a number of times before I came along. I was advised by another Boss Hoss guru to use VW exhaust flanges. I went to my, local, muffler guy and asked for some. He said he cannot get them any longer because VWs are obsolete. He's been in the business for many years, so I didn't argue with him. I jumped online and found them for 8 bucks each. Now, Jack and Mary Ellen La Fong didn't raise any fools, so I saved my 32 clams and made my own out of a hunk of 2 X 1/8" flat stock that I already had. Hole sawed them out, drilled a 5/16" hole in each corner and there ya go. I could have made 2 or 3 hole flanges, but 4 holes was easier and faster. The, somewhat, tricky part was cutting the crossmember out. I remembered an old trick for cutting tubing nice and square freehanded. Wrap a worm drive hose clamp around the tube, snug it down and use the edge of the clamp as a guide. My Sawzall took a dump, so I used a jigsaw with a fine toothed metal cutting blade. This all needs to be done with the frame still bolted to the engine so alignment is maintained. The flanges were bolted together in pairs, slipped over the stubs on the frame and the severed crossmember was put back into place. The flanges were then slid so one was on the stub and the other was on the crossmember. After everything was square to the world, all four flanges were tacked in place. The crossmember was then removed and the flanges were securely welded in place from the inside for a clean look.

Tuesday, November 23, 2010

You'll Put Yer Eye Out, Kid




I received a call today from another BH tinkerer. His first words were, "Yer gonna kill yerself with those mounts." It seems that my assumption about the mounts and their intended function was all wrong. They are not there to keep the engine from moving up, down or around. They are to keep the frame downtubes from bowing out towards the front of the bike. It makes sense to me. So, I grabbed the ol' die grinder and off they came. He sent pictures to me some time ago of his mounts. They are nice, but he has different heads than I do and he doesn't have the same bolt holes as mine. Still, I should be able to come up with a similar setup. Time for some more head scratchin'

OK, boys and girls. I laid awake for almost 10 minutes last night and came up with, what I consider to be, a solution to the various issues that have been raised by experienced bikers, fraidy cats and naysayers (BTW, stop saying nay). There will be no welding on the frame and the mounts will be rigid enough to stop any, potential, movement in any direction. I have finished the right side. I cut a piece of 1/2 plate and drilled it to match the holes in my head (no, not that one, smartass). Using the original BH mounts, I drilled and tapped two more holes in the plate to match up with the holes in the mounts. The left side will be, somewhat similar, only with a much thinner plate bolted to the head because of the cylinder offset.

Later that afternoon.
Finished the left side. Since it is too thin to tap threads into, I welded a short, threaded bung onto the plate for the outer bolt. The other bolt goes through the plate and into the head. The BH mount lined up almost perfectly with the hole in the head. I just had to ream it a bit for wiggle room. All of the exposed bolts will get proper spacers to insure that the mounts all suck up tight to the heads.